Thursday, 29 December 2016

Christmas 2016

Hello all. I hope you have all had a lovely Christmastime......I'm afraid I've not touched my minis over the holidays but I did get a little time just beforehand to finish off the downstairs hallway and first floor landing. These are the first two areas to be completed and I'm happy with how they've turned out.

After getting the lighting sorted out and the wallpaper done I got the flooring laid and the cornice and skirting boards fitted. Then it was just a matter of making some curtains for the window on the landing....I needed to do that before the staircase is fitted leading up to the second floor as it won't be accessible after that.
You can just see a glimpse of this window in the photo here.


The doors aren't glued in yet until the rooms on the other side are decorated. I found a good way of making 'porcelain' door knobs by using nail polish! I'm pleased with how they look and they make a change from having brass ones.....


I need to fit the stair rods and put back all the spindles I knocked off whilst fitting the carpet....but I just wanted to see how it is going to look! 


The downstairs entrance hall is now complete apart from the door which needs gluing once I have decorated the shop area. I'm really happy with it and especially pleased that my working grandfather clock fits just right in there and is the first thing I see when I open the door.

At the other side of this landing wall is the kitchen and parlour. I think these are the next two rooms I'm going to be working on. 
The chimney breasts are fitted in both the kitchen and the parlour and both the fires are wired up.....



And here we are looking all festive! 





Monday, 5 December 2016

Some inside progress!

At last I've moved indoors but not until after I had done lots of staring and thinking before doing so! I really had to do this to be sure of my work plans so that I get everything done in the right order as I go along. Building, decorating and lighting a 3d building is abit of a mind boggling affair! To work it all out I sat down and wrote a plan of action - where to route the wires for the lighting and which piece of wall can I stuck in and when?  Can I lay this flooring now, at which point will I need to glaze that window and add curtains....? etc etc.
Well the first thing I decided to do was to make the channels for the lighting wires to go through to the back of the building....I knew I had to do this before any walls could be stuck in place or flooring laid. The chimney breasts were glued into position at this stage too so that I could get the wires lined up for the fires....


So far so good - the channels for the wires from the shop lights downstairs and for both fires on the first floor


My channels are a little wonky as I used the Dremel but they will still do the job.


The shop light coming up into the sitting room and the wire coming into the back of the fireplace ready to connect to the kitchen range and the sitting room fire.


Here you can see the wires laid in and covered with masking tape


And both the fire lights working! Hooray!


Next I needed to get the hallway and landing wallpapered so that I could glue in the two back walls. I also fixed the wall lights into place before sliding and gluing the wall between the landing and the other two rooms on the first floor. It maybe a challenge putting in the cornice and skirting as this area is quite deep. Wish me luck! I will be able to remove the window to glaze it and add curtains.

            

This is the first floor landing. I'm so pleased with how it's looking so far....


The stairs leading to the attic floor and the doors to the kitchen and sitting room not glued in place yet.


This next picture shows the downstairs entrance hall with the stairs and wall now glued into position and the doorway leading into the shop area.
It took me ages to fix the brass stair rods and I have another set to do yet!
Skirting boards, cornice, door knobs and light switches to add....


Having done all this I had to have a little play and see how my shelving would fit into the shop. I bought a few at the York Fair as I was undecided in how I was going to arrange them. I toyed with the idea of blocking off the
trade entrance door entirely, which would have added more shelf space but I feel I would lose some of the 3d aspect doing that which is what I really love about this building.  I'm thinking this arrangement in the following photos is how I'm going to go.... As you can see there will be a little back lobby area near the tradesman's entrance door and I plan to put another door leading into my Orangery on that back wall next to it. I think this will add extra interest. All I need to do now is decide on the finish for those shelves! Stained or painted...? I suppose to be in keeping with the Edwardian era they would probably have been in oak but I'm afraid that will make it look terribly dark in here....I'm wondering about a distressed cream or pale green colour....? Mmmmm....? (The light fitting on these pictures is only temporary.)





So you are up to date with where I am up to for now...thankyou for looking in!